Introduce
We have a total of three electronic screen, they are LCD-2000-3916/LCD-2000-9225/LCD-2000-7775. They are single-chip controller, and all of them can display to a maximum of 176-RGB x 220 -dot graphics on 262k-color TFT panel. The chip can be connected to the outside of the microprocessor directly. And accept the 8-bit high speed bus interface and serial peripheral interface. The display data can be stored in the memory for data RAM which is 176×220×18 bits.
We provided development kit include:
1, All chip's datasheet
2, Arduino driver and sample code
3, Application notes for Arduino UNO and Arduino Mega2560
4, Source code for STM32
5, Schematic
Features
Ø Drive 2.0-inch TFT screen LCD-2000
Ø Display resolution: 176(H)×220(V)
Ø Display data RAM: 176×220 ×18bits=696960bits
Ø Display mode: Full color mode, 262K-colors, 8-colors
Ø Pin set: DB0-DB7 is IO port for data transmission, WR/RS/CS/LE/RST/PWM is control pin
Ø Supports 8-bit micro-controller interface 8080 series
Ø IO port power supply voltage: 1.65-3.5V
Ø Low power consumption
MEGA 2560 R3
■INTRODUCTION
MEGA 2560 R3 is an Arduino compatible board, It’s based on Arduino MEGA 2560 design, So you can use BUONO MEGA 2560 as Arduino MEGA 2560, All Code, shield and IDE for Arduino MEGA 2560 R3 are also valid on BUONO MEGA 2560, Some visible improvement on hardware make BUONO more flexible and easier use, For example : 3.3V or 5V IO selectable allow you connect some 3.3V modules (such as XBee) to BUONO directly.
■FEATURES
l Inherits all of Arduino MEGA 2560's features
l Compatible to Arduino MEGA 2560's pin layout, screw hole and dimensions
l 3.3V or 5V operating voltage selectable
l More visible location of indication LEDs
l Evolved with SMD components
l Digital I/O pins 54(of which 15 provied PWM output)
l Analog Input pins 16
l Flash memory 256 KB or which 8KB used by bootloader
l SRAM 8 KB
l EEPROM 4KB
l Clock speed 16MHz
l Micro USB connection make the cable can be mixed use with most digital products such as cell phone
l 5V DC/DC provide 95% efficiency
l 6V to 23V width rang input
l Provide max 1.8A for peripheral circuits
l Ground terminal make measurement easier
■THE DIFFERENCE BETWEEN Arduino MEGA 2560 AND BUONO MEGA 2560
|
Arduino MEGA 2560
|
BUONO MEGA 2560
|
USB Connector
|
Type B Female
|
Micro USB connector
|
Operating Voltage
|
5V
|
3.3V or 5V selectable
|
3.3V Current
|
50mA
|
600mA
|
5V Current
|
500mA
|
1.8A
|
Input Range
|
7V to 12V
|
6V to 23V
|
MCU
|
ATMEGA2560
|
ATMEGA2560
|
Others
|
|
Ground terminal
LPF for AVCC
|
|
|
|
LCD PCB Adapter
The TFT LCD PCB Adapter for MEGA 2560 is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board.
Package list:
1PCS 2.0" TFT LCD Module
1PCS LCD PCB Adapter
1PCS Mega 2560
1PCS USB cable
4 set screw and nut
