TFT LCD Shield for MEGA 2560

Introduce

The TFT LCD PCB Adapter for MEGA 2560 is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board. It can be used with a MEGA 2560 and LCD display.

      

TFT LCD Shield for UNO R3

The TFT LCD PCB Adapter for UNO is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board. It can be used with a UNO and LCD display.

 

 

LCD-2000-7775

Introduce

We have a total of three electronic screen, they are LCD-2000-3916/LCD-2000-9225/LCD-2000-7775. They are single-chip controller, and all of them can display to a maximum of 176-RGB x 220 -dot graphics on 262k-color TFT panel. The chip can be connected to the outside of the microprocessor directly. And accept the 8-bit high speed bus interface and serial peripheral interface. The display data can be stored in the memory for data RAM which is 176×220×18 bits.

We provided development kit include :

1, All chip's datasheet

2, Arduino driver and sample code

3, Application notes for Arduino UNO and Arduino Mega2560

4, Source code for STM32

5, Schematic

Features

Ø  Drive 2.0-inch TFT screen LCD-2000

Ø  Display resolution: 176(H)×220(V)

Ø  Display data RAM : 176×220 ×18bits=696960bits

Ø  Display mode: Full color mode, 262K-colors, 8-colors

Ø  Pin set: DB0-DB7 is IO port for data transmission, WR/RS/CS/LE/RST/PWM is control pin

Ø  Supports 8-bit micro-controller interface 8080 series

Ø  IO port power supply voltage:1.65-3.5V

Ø  Low power consumption

  

BUONO UNO USB Cable 2.0\" \' inch TFT LCD Module PCB Adapter Kit for Arduino STM32

Introduce

We have a total of three electronic screen, they are LCD-2000-3916/LCD-2000-9225/LCD-2000-7775. They are single-chip controller, and all of them can display to a maximum of 176-RGB x 220 -dot graphics on 262k-color TFT panel. The chip can be connected to the outside of the microprocessor directly. And accept the 8-bit high speed bus interface and serial peripheral interface. The display data can be stored in the memory for data RAM which is 176×220×18 bits.

We provided development kit include:

1, All chip's datasheet

2, Arduino driver and sample code

3, Application notes for Arduino UNO and Arduino Mega2560

4, Source code for STM32

5, Schematic

Features

Ø  Drive 2.0-inch TFT screen LCD-2000

Ø  Display resolution: 176(H)×220(V)

Ø  Display data RAM: 176×220 ×18bits=696960bits

Ø  Display mode: Full color mode, 262K-colors, 8-colors

Ø  Pin set: DB0-DB7 is IO port for data transmission, WR/RS/CS/LE/RST/PWM is control pin

Ø  Supports 8-bit micro-controller interface 8080 series

Ø  IO port power supply voltage: 1.65-3.5V

Ø  Low power consumption

BUONO UNO R3

■ INTRODUCTION

BUONO UNO R3 is an Arduino compatible board, It’s based on Arduino UNO R3 design, So you can use BUONO UNO as Arduino UNO, All Code, shield and IDE for Arduino UNO R3 are also valid on BUONO UNO, Some visible improvement on hardware make BUONO more flexible and easier use , For example: 3.3V or 5V IO selectable allow you connect some 3.3V modules (such as XBee) to BUONO directly.

 ■ FEATURES

l Inherits all of Arduino UNO’s features

l Compatible to Arduino UNO/Duemilanove’s pin layout, screw hole and dimensions

l 3.3V or 5V operating voltage selectable

l More visible location of indicator LEDs

l Evolved with SMD components

l Digital I/O pins 14 (of which 6 provied PWM output)

l Flash memory 32KB or which 0.5KB used by bootloader

l SRAM 2KB

l EEPROM 1KB

l Clock speed 16MHz

l Micro USB connection make the cable can be mixed use with most digital products such as cell phone

l 5V DC/DC provide 95% efficiency

l 6V to 23V width rang input

l Provide max 1.8A for peripheral circuits

l LC Low pass filter for AVCC make ADC much stable

l Ground terminal make measurement easier

 ■ THE DIFFERENCE BETWEEN BUONO UNO R3 AND ARDUINO UNO

                                                                                         

	Arduino UNO R3	BUONO UNO R3
USB   Connector	Type   B Female	Micro   USB connector
Operating   Voltage	5V	3.3V   or 5V selectable
3.3V   Current	50mA	300mA
5V   Current	500mA	2A
Input   Range	7V   to 12V	6V   to 23V
MCU	Atmega168   or Atmega328	Atmega328   TQFP-32
Others		Ground terminal LPF for AVCC LITE version available

                

LCD PCB Adapter

The TFT LCD PCB Adapter for MEGA 2560 is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board.

     

BUONO UNO USB Cable 2.0" 2.0 inch TFT LCD Module PCB Adapter Kit for Arduino STM32

Introduce

We have a total of three electronic screen, they are LCD-2000-3916/LCD-2000-9225/LCD-2000-7775. They are single-chip controller, and all of them can display to a maximum of 176-RGB x 220 -dot graphics on 262k-color TFT panel. The chip can be connected to the outside of the microprocessor directly. And accept the 8-bit high speed bus interface and serial peripheral interface. The display data can be stored in the memory for data RAM which is 176×220×18 bits.

We provided development kit include:

1, All chip's datasheet

2, Arduino driver and sample code

3, Application notes for Arduino UNO and Arduino Mega2560

4, Source code for STM32

5, Schematic

Features

Ø  Drive 2.0-inch TFT screen LCD-2000

Ø  Display resolution: 176(H)×220(V)

Ø  Display data RAM: 176×220 ×18bits=696960bits

Ø  Display mode: Full color mode, 262K-colors, 8-colors

Ø  Pin set: DB0-DB7 is IO port for data transmission, WR/RS/CS/LE/RST/PWM is control pin

Ø  Supports 8-bit micro-controller interface 8080 series

Ø  IO port power supply voltage: 1.65-3.5V

Ø  Low power consumption

BUONO UNO R3

■ INTRODUCTION

BUONO UNO R3 is an Arduino compatible board, It’s based on Arduino UNO R3 design, So you can use BUONO UNO as Arduino UNO, All Code, shield and IDE for Arduino UNO R3 are also valid on BUONO UNO, Some visible improvement on hardware make BUONO more flexible and easier use , For example: 3.3V or 5V IO selectable allow you connect some 3.3V modules (such as XBee) to BUONO directly.

 ■ FEATURES

l Inherits all of Arduino UNO’s features

l Compatible to Arduino UNO/Duemilanove’s pin layout, screw hole and dimensions

l 3.3V or 5V operating voltage selectable

l More visible location of indicator LEDs

l Evolved with SMD components

l Digital I/O pins 14 (of which 6 provied PWM output)

l Flash memory 32KB or which 0.5KB used by bootloader

l SRAM 2KB

l EEPROM 1KB

l Clock speed 16MHz

l Micro USB connection make the cable can be mixed use with most digital products such as cell phone

l 5V DC/DC provide 95% efficiency

l 6V to 23V width rang input

l Provide max 1.8A for peripheral circuits

l LC Low pass filter for AVCC make ADC much stable

l Ground terminal make measurement easier

 ■ THE DIFFERENCE BETWEEN BUONO UNO R3 AND ARDUINO UNO

                                                                                         

	Arduino UNO R3	BUONO UNO R3
USB   Connector	Type   B Female	Micro   USB connector
Operating   Voltage	5V	3.3V   or 5V selectable
3.3V   Current	50mA	300mA
5V   Current	500mA	2A
Input   Range	7V   to 12V	6V   to 23V
MCU	Atmega168   or Atmega328	Atmega328   TQFP-32
Others		Ground terminal   LPF for AVCC   LITE version available

                

LCD PCB Adapter

The TFT LCD PCB Adapter for MEGA 2560 is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board.

Package list:

1PCS 2.0" TFT LCD Module

1PCS LCD PCB Adapter

1PCS BUONO UNO R3 

1PCS USB cable

4 set screw and nut

Introduce

We have a total of three electronic screen, they are LCD-2000-3916/LCD-2000-9225/LCD-2000-7775. They are single-chip controller, and all of them can display to a maximum of 176-RGB x 220 -dot graphics on 262k-color TFT panel. The chip can be connected to the outside of the microprocessor directly. And accept the 8-bit high speed bus interface and serial peripheral interface. The display data can be stored in the memory for data RAM which is 176×220×18 bits.

We provided development kit include:

1, All chip's datasheet

2, Arduino driver and sample code

3, Application notes for Arduino UNO and Arduino Mega2560

4, Source code for STM32

5, Schematic

Features

Ø  Drive 2.0-inch TFT screen LCD-2000

Ø  Display resolution: 176(H)×220(V)

Ø  Display data RAM: 176×220 ×18bits=696960bits

Ø  Display mode: Full color mode, 262K-colors, 8-colors

Ø  Pin set: DB0-DB7 is IO port for data transmission, WR/RS/CS/LE/RST/PWM is control pin

Ø  Supports 8-bit micro-controller interface 8080 series

Ø  IO port power supply voltage: 1.65-3.5V

Ø  Low power consumption

MEGA 2560 

■INTRODUCTION 

MEGA 2560 R3 is an Arduino compatible board, It’s based on Arduino MEGA 2560 design, So you can use BUONO MEGA 2560 as Arduino MEGA 2560, All Code, shield and IDE for Arduino MEGA 2560 R3 are also valid on BUONO MEGA 2560, Some visible improvement on hardware make BUONO more flexible and easier use,  For example : 3.3V or 5V IO selectable allow you connect some 3.3V modules (such as XBee) to BUONO directly.

■FEATURES

l  Inherits all of Arduino MEGA 2560's features

l  Compatible to Arduino MEGA 2560's pin layout, screw hole and dimensions

l  3.3V or 5V operating voltage selectable

l  More visible location of indication LEDs

l  Evolved with SMD components

l  Digital I/O pins 54(of which 15 provied PWM output)

l  Analog Input pins 16

l  Flash memory 256 KB or which 8KB used by bootloader

l  SRAM 8 KB

l  EEPROM 4KB

l  Clock speed 16MHz

l  Micro USB connection make the cable can be mixed use with most digital products such as cell phone

l  5V DC/DC provide 95% efficiency

l  6V to 23V width rang input

l  Provide max 1.8A for peripheral circuits

l  Ground terminal make measurement easier

■THE DIFFERENCE BETWEEN Arduino MEGA 2560 AND BUONO MEGA 2560

	Arduino MEGA 2560	BUONO MEGA 2560
USB Connector	Type B Female	Micro USB connector
Operating Voltage	5V	3.3V or 5V selectable
3.3V Current	50mA	600mA
5V Current	500mA	1.8A
Input Range	7V to 12V	6V to 23V
MCU	ATMEGA2560	ATMEGA2560
Others		Ground terminal LPF for AVCC

                

LCD PCB Adapter

The TFT LCD PCB Adapter is compatible with Arduino pins, user can directly plug the TFT LCD PCB Adapter in the shield and stand on the Arduino board.

Package list:

1PCS 2.0" TFT LCD Module

1PCS LCD PCB Adapter

1PCS Mega 2560 

1PCS USB cable

4 set screw and nut